FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Alpharetta Owner’s Guide

FAAC hinge and roller replacement in Alpharetta typically runs $280-$520 installed, depending on whether we’re working on a single residential swing gate or a dual-leaf commercial setup with heavier 412 or 415 series hardware. We stock FAAC-compatible hinges and rollers on every service truck, and most replacements are completed same-day once we verify the model and pin diameter on site. Homeowners usually notice the problem first as a grinding scrape at the end of the open cycle, or the gate hanging lower on one side until the motor strains and faults out.

Call (678) 679-2152

Which FAAC Models This Applies To

FAAC manufactures several gate families, and the hinge and roller assemblies are not interchangeable across series. The 391, 402, 412, and 415 swing-gate operators use distinct bracket geometries, and the roller wheels on FAAC slide-gate systems, particularly the 746 and 844 series, carry different axle diameters and bushing specs. We see the most hinge wear in Alpharetta on the 412 and 415 residential swing arms, where the cast aluminum hinge body meets a steel pin and galvanic corrosion sets in after five to seven years of exposure to Georgia’s humidity cycles.

To identify your part, locate the FAAC data plate on the motor housing, not the gate leaf itself. The plate lists the series, production year, and voltage. For hinges, we measure the pin diameter with a caliper, check whether the gate uses a top-hinge or side-mount bracket, and note the bolt pattern spacing. FAAC OEM hinges carry part numbers like 63000935 or 63001014, but we also install quality aftermarket equivalents from Elite Gate Systems that match the same tensile rating at roughly 60 percent of OEM cost. The aftermarket option carries the same 365-Day Done Right Promise, and we document the part source in your job record either way.

Vance Gate Repair Alpharetta is an independent service provider with no affiliation to FAAC. We service the brand because we stock the parts and know the hardware, not because we’re contractually bound to.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate drops visibly on the hinge side when fully open. The internal bushing has worn eccentric, allowing the pin to settle lower in the housing. On FAAC 412 series gates in Alpharetta, we measure this with the gate at 90 degrees; anything more than 3/16 inch of sag means the bushing is gone and the pin is scoring the aluminum body.
• A rhythmic grinding or squeal at the end of the open or close cycle. The roller has flat-spotted or the bearing has lost grease. FAAC rollers use sealed bearings that cannot be repacked; once the seal fails, grit from driveway runoff accelerates wear, and the noise is the bearing race starting to spall.
• The motor draws high current and trips the control board overload. The gate is binding because a seized roller or distorted hinge is adding mechanical resistance. We check this with an amp clamp on the motor leads; a FAAC 415 drawing over 8 amps under normal load almost always has a hardware problem, not a motor problem.
• Visible rust streaks or white aluminum oxide below the hinge. This is galvanic corrosion between the steel pin and aluminum hinge body, common in Alpharetta where afternoon thunderstorms keep hardware wet and the overnight humidity prevents full drying. By the time you see the stain, the pin is often frozen in the bore.
• The gate has shifted and now catches the stop post or ground stop. A worn hinge allows the gate leaf to migrate in its arc. We see this on longer driveway gates near Windward and Avalon, where a 16-foot leaf with even 1/4 inch of hinge slop translates to several inches of misalignment at the far end.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: whether the pin is frozen and needs extraction with a press or torch, whether the gate leaf must be supported and realigned after hinge replacement, and whether the existing hardware uses metric or older imperial bolt patterns that require adapter bushings. Every price is written and handed to you before we pick up a tool, under Haven Standard Clause 1. The installed price includes the part, labor, realignment check, and a photo log of the work. All hinge and roller replacements are covered by our 365-Day Done Right Promise.

DIY or Call Us?

There is a safe middle ground here. A homeowner can inspect the hinge for visible cracks, measure gate sag with a level, and check whether the roller turns freely by hand with the gate in manual release. What we do not recommend is attempting hinge pin extraction or roller replacement on a loaded gate leaf. The torsion and weight involved can cause serious injury if the gate shifts unexpectedly, and FAAC 415 series arms in particular can weigh 180 pounds or more per leaf.

We have the jack stands, chain hoists, and press tools on every truck. More importantly, we have the documentation habit: before we touch anything, we photograph the existing condition, record the model and serial, and note the limit-switch settings so nothing is lost in the swap. When we’re done, you get the photo record and the written scope. Name what you found. Name what it costs. Name what you left behind.

For a free written estimate on your FAAC hinge or roller replacement in Alpharetta, call us at (678) 679-2152. A live person answers, 24 hours a day.

FAQs