Gate Installation in Alpharetta - Written Price, Install Date Set

Trusted Gate Installation for Alpharetta Homeowners

A new Alpharetta Gate Installation typically costs between $2,800 and $8,500 depending on gate type, material, and automation needs, with most projects completed in 1-3 days after final measurements. Vance Gate Repair Alpharetta has installed and documented over 22,000 gates since 2014, and every installation starts with a written price before any work begins - that’s Haven Standard Clause 1. If your current gate is sagging, rusted through, or you’re building new and need a secure entry point that matches your property, call us at (678) 679-2152 for a free measure and written estimate.

Call (678) 679-2152

We serve homeowners throughout Alpharetta’s neighborhoods - from the estate properties off Webb Bridge Road to the newer builds in Avalon and the established homes near Wills Park. Alpharetta’s clay-heavy soil and freeze-thaw cycles in North Fulton County put specific stress on gate posts and footings. We’ve learned to account for that in our depth and drainage specs. Our technicians are background-checked, uniformed, and you’ll get a name and photo before anyone arrives at your Alpharetta property.

What Our Gate Installation Service Includes

Driveway Gate Installation in Alpharetta

A Driveway Gate is the primary vehicle entry point for your Alpharetta property, typically spanning 10-16 feet for single openings or up to 24 feet for double configurations. You need one when you’re replacing a failed gate, completing new construction, or upgrading from a manual chain to automated entry. At Vance Gate Repair Alpharetta, we measure your drive slope, check setback requirements with Fulton County’s typical residential standards, and specify post depth to 36 inches minimum with gravel drainage to handle Alpharetta’s expansive clay soil.

Pedestrian Gate Installation in Alpharetta

A Pedestrian Gate is a human-scale entry point, usually 3-4 feet wide, separate from vehicle access and often matching the style of your main driveway gate. You need one when you have foot traffic from a sidewalk, a pool enclosure requiring code-compliant self-closing hardware, or a side yard path that needs controlled access. We install pedestrian gates with the same documentation habit we use on commercial sites - photographed post plumb, hinge torque spec, and latch alignment recorded before we leave your Alpharetta property.

Sliding Gate Installation in Alpharetta

A sliding gate runs parallel to your fence line on a track or cantilever system, making it the right choice when your Alpharetta driveway has limited swing radius or slopes upward from the street. You need one when a swing gate would hit parked cars, when you have 8+ feet of parallel fence run available, or when you want the gate fully inside your property line. Our Alpharetta sliding gate installations include a laser-leveled track bed, concrete footing with rebar cage, and limit-switch programming documented with photos of the final gate positions.

Swing Gate Installation in Alpharetta

A swing gate rotates on hinge posts, either single-leaf or double-leaf, and remains the most common residential style in Alpharetta’s subdivisions. You need one when you have adequate swing clearance, prefer a traditional appearance, or want lower maintenance than a track-dependent sliding system. We spec hinge posts at 6×6 minimum for wood or 4-inch square steel for metal gates, set in concrete to 42 inches in Alpharetta’s frost-prone northern suburbs, with the post plumb checked and photographed at three angles.

Double Gate Installation in Alpharetta

A double gate uses two leaves that meet in the center, reducing the swing arc per leaf and allowing wider openings without the machinery of a sliding system. You need one when your Alpharetta driveway exceeds 14 feet, when you want the visual symmetry of paired gates, or when a single large leaf would stress hinges and automation over time. We install double gates with a center drop pin or magnetic latch, adjustable center stops, and synchronized automation arms - the limit settings for each leaf documented separately in your job record.

Security Gate Installation in Alpharetta

A security gate prioritizes controlled access with features like keypad entry, intercom integration, loop detectors, and anti-climb design - common for Alpharetta properties on larger lots or with home office traffic. You need one when you’re restricting access to a business entrance, adding a second controlled point to an estate property, or replacing a decorative gate with something that actively manages who enters. Our security gate installations in Alpharetta include conduit runs for power and low-voltage, photo-eye placement at 18 inches and 36 inches per safety standards, and a wiring diagram left with you under Haven Standard Clause 4.

Brands We Service for Gate Installation

We install and automate gates using equipment from nine major brands, and we don’t steer you toward one manufacturer because it’s easier for us. If your Alpharetta property already has BFT operators, we’ve installed hundreds of their hydraulic swing and sliding systems and stock their OEM control boards and limit sensors. For Linear equipment, we carry their actuator arms and control modules, and we’re familiar with their programming sequences for residential and light commercial settings. Viking operators are common on heavier gates in Alpharetta’s estate neighborhoods - we’ve installed their V-series slide operators on 20-foot aluminum cantilever systems and documented the chain tension and limit-switch settings on each.

We also work with Ghost Controls for solar-compatible residential swing applications, particularly on Alpharetta properties where running 110V to the gate would require trenching through established landscaping. Whether you have Ghost Controls, BFT, Linear, Viking, or any other make - including FAAC, DoorKing, Elite, or Mighty Mule - we can install, automate, and document the system. Our only requirement is that the written price is agreed before we pick up a tool.

Before

After

Signs You Need Gate Installation Right Now

• The gate frame is cracked or separating at welded joints. A cracked frame won’t hold adjustment, and welding on-site without removing the gate rarely lasts through Alpharetta’s temperature swings. We see this most often on older steel gates in the Windward and Country Club of the South areas, where the original installation used inadequate penetration or no gusset plates at stress points.
• The posts lean visibly or move when the gate operates. Post movement means the footing has failed, either from inadequate depth, poor drainage, or the clay soil expansion that shifts everything in North Fulton County. A leaning post takes the gate out of square and burns up automation motors trying to pull a binding load.
• You’re operating the gate manually because the automation failed and repair exceeds replacement value. This is common with gates over 15 years old where the motor, control board, and safety edges all need attention at once. We can price a new automated system against piecemeal repair, both in writing, so you decide with real numbers.
• The gate doesn’t match your property’s current use or security needs. Maybe you added a pool and need code-compliant self-closing hardware, or your home office sees client traffic that requires keypad access instead of getting out to open manually. A new installation lets you spec for how you actually live now, not how the previous owner lived in 2005.
• You’re completing new construction and the builder left a gate opening with no gate. This happens more than you’d think in Alpharetta’s custom builds - the masonry columns go in, the driveway gets paved, and the gate itself was an afterthought. We measure the opening, spec the gate and automation together, and coordinate with your electrician on conduit placement before the landscaping goes in.

Our Gate Installation Process - Step by Step

1. 1
   Free measure and written estimate. We visit your Alpharetta property, measure the opening, check slope and clearance, note any electrical or conduit needs, and photograph the site. Within 24 hours you receive a written price with line-item breakdown - gate material, automation components, labor, and any electrical subcontracting. No work starts until you approve the written scope and price. That’s Haven Standard Clause 1.
2. 2
   Fabrication and material ordering. Once approved, we order your gate and automation components. Lead times vary: aluminum stock gates typically 2-3 weeks, custom wrought iron or steel 4-6 weeks, automation components 1-2 weeks if in stock. We don’t take deposit money before we have confirmed delivery dates from our suppliers.
3. 3
   Site preparation and post setting. On installation day, we excavate post holes to spec depth with gravel drainage base, set posts in concrete, and verify plumb with a digital level. In Alpharetta’s clay soil, we use a 4-inch gravel collar around each post base to wick water away from the concrete. Photos of post depth, plumb reading, and drainage detail go into your job record under Clause 4.
4. 4
   Gate hanging and automation mounting. We hang the gate, check swing or slide travel for binding, mount the operator with proper arm geometry or chain tension, and install safety devices - photo eyes, edge sensors, loop detectors as specified. Every limit switch is set and photographed at its final position. The control board programming is saved to our records with a backup photo of the display settings.
5. 5
   Final test, documentation, and walkthrough. We cycle the gate 20+ times under various conditions, test all safety reversals, demonstrate keypad or remote programming, and leave you with the photo log, wiring diagram, written record of part numbers installed, and the 365-Day Done Right Promise documentation. You know exactly what was done and what was set before we leave your Alpharetta property.

How Much Does Gate Installation Cost in Alpharetta?

Gate Installation Near Alpharetta - Our Service Area

We install gates throughout North Fulton and the surrounding metro area. From Alpharetta, typical drive times put us in Roswell in 15 minutes, Johns Creek in 10, Milton in 20, and Duluth or Sandy Springs in 25. We also regularly work in Norcross, Cumming, Sugar Hill, Holly Springs, North Atlanta, and Lilburn. Our technicians live in the area, so we’re not dispatching from a central warehouse across the Perimeter during rush hour. For installation work, we schedule a specific date after your written approval, with a 2-hour arrival window and a call 30 minutes out.

Frequently Asked Questions - Gate Installation in Alpharetta

Schedule Your Gate Installation Service in Alpharetta Today

Call (678) 679-2152 to schedule your free measure and written estimate. A live person answers 24 hours a day, seven days a week - no automated attendant, no callback queue. We’ll visit your Alpharetta property, spec the right gate and automation for your actual conditions, and deliver a line-item price in writing before any work is scheduled. Under The Haven Standard, you get the written price, the documented photo record, and the 365-Day Done Right Promise on every installation. No obligation, no deposit required to get your estimate.

Written by Adrian Vance, Owner at Vance Gate Repair, serving Alpharetta since 2014.