Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Marietta, GA
Gate access control repair in Marietta typically costs $280-$650 for keypad or intercom fixes and $180-$420 for remote receiver troubleshooting, with most East Cobb calls completed same-day. We carry FAAC, BFT, Linear, and Viking control boards in our Atlanta-stocked van, so a failed keypad in Indian Hills or a dead receiver near Pope High School doesn’t wait on parts shipping. Call (678) 679-2152 for a written quote before any work starts.
Marietta’s concentration of 20-35 year old automated gate systems means access control failures here are usually component degradation, not installation error. We document every control board swap and keypad programming with photos under The Haven Standard, so the next technician sees exactly what we found and what we left behind.
Why Marietta Homes Are Different
East Cobb’s HOA-governed subdivisions were built predominantly from the mid-1980s through the early 2000s, which means the Viking, Elite, and Linear operators on many Marietta gates are now past their designed service life. The brick-column anchors that hold these gates are showing mortar fatigue, and HOA covenants require like-for-like finishes with prior architectural review approval, so repairs demand finish spec sheets and color-matched powder coating, not generic substitutions.
Marietta’s Georgia Piedmont red clay expands when wet and shrinks in summer drought, causing gate posts and brick columns to heave seasonally. This chronic misalignment is the single most common repeat-repair call we get from the Murdock Road corridors. Heavy mature hardwood canopy across Cobb County means falling limbs after summer thunderstorms account for a significant share of sudden gate frame damage.
Downtown-adjacent neighborhoods hold older wood privacy fence gates from the 1950s-70s with entirely different repair needs, simpler hardware, and no automation to troubleshoot.
Our Main Marietta Services
Most Marietta calls fall into three categories, each with its own dedicated page.
Gate Repair in Marietta
We repair ornamental iron swing gates on brick pillar entries, sagging wood privacy gates, and storm-damaged frames across East Cobb and downtown-adjacent neighborhoods. Every repair starts with a written price and ends with a photographed record of what was found and what was fixed. Gate Repair in Marietta
Gate Installation in Marietta
New gate installation in Marietta requires navigating active HOA architectural review boards, matching existing ornamental iron profiles, and anchoring to red clay that shifts seasonally. We measure, spec, and quote in writing before ordering materials. Gate Installation in Marietta
Gate Motor & Opener in Marietta
Motor replacement on 20-35 year old Viking, Elite, and Linear operators is common in East Cobb estates. We service nine automation brands and stock control boards locally, so diagnosis and repair don’t wait on shipping. Gate Motor & Opener in Marietta
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Marietta
Access control repair in Marietta centers on aging keypad, intercom, and remote systems installed during the original construction boom of the 1980s-2000s. These components fail from moisture intrusion, UV-degraded wiring, and obsolete radio frequencies, not from rough use. Because HOA communities here require documented approval for any visible hardware change, we photograph every existing device before removal and provide the homeowner with a spec sheet for architectural review submission. Gate Access Control work in Marietta demands this documentation discipline.
Keypad Entry
Signs you need it
Buttons stick or don’t register, the housing is cracked from freeze-thaw cycles, or the gate opens without code entry indicating a shorted ribbon cable.
What it costs in Marietta
Keypad replacement runs $280-$450 for standard weather-resistant models and $380-$650 for cellular-enabled or HOA-mandated finish-matched units.
How we do it
We photograph the existing mounting position and wiring, match the finish spec to HOA requirements, program new codes with the homeowner present, and document the serial number and programming sheet before leaving.
Remote Control
Signs you need it
Remote works intermittently from 50+ feet, the LED dims, or multiple remotes fail simultaneously pointing to a receiver board issue rather than individual remote failure.
What it costs in Marietta
Remote receiver replacement costs $180-$320; individual remote programming or replacement runs $45-$85 per unit.
How we do it
We test signal strength at the gate and from the typical approach distance, replace the receiver if multiple remotes are affected, program all remotes to the new frequency, and record the DIP switch or rolling code settings in the job file.
What Gate Access Control Costs in Marietta
| Item | Typical range in Marietta |
|---|---|
| Keypad entry replacement | $280-$650 |
| Remote receiver replacement | $180-$320 |
| Remote programming (per unit) | $45-$85 |
Can you program new remotes for an old Viking operator?
Yes. We stock compatible receivers and remotes for Viking systems and can bridge modern rolling-code remotes to older fixed-code operators without full motor replacement. Call (678) 679-2152 for a free compatibility check.
Will HOA approval delay my keypad repair?
Not the repair itself. We provide the finish spec sheet and photo documentation you need for HOA filing, and we can install a temporary matching unit while paperwork processes if the gate is inoperable.
Gate Parts & Welding in Marietta
Welding and parts replacement in Marietta addresses two distinct problems: storm-damaged ornamental iron from falling hardwood limbs, and chronic hinge or post failure from red clay heave. The 20-35 year old gates in East Cobb estates often need rail repair or custom welding to match original profiles rather than full replacement, while downtown-adjacent wood gates need hinge and post work. We carry a mobile welder and stock common hinge and roller sizes, so most Marietta welding calls need no return visit. Gate Parts & Welding documentation includes pre- and post-weld photos under Haven Standard Clause 4.
Hinge Replacement
Signs you need it
The gate drags at the latch side, gaps unevenly when closed, or the hinge pin has visible vertical play exceeding 1/8 inch.
What it costs in Marietta
Standard ornamental iron hinge replacement runs $140-$280 per hinge; heavy-duty ball-bearing upgrades for gates over 400 lbs run $220-$380.
How we do it
We support the gate with a portable lift, remove the failed hinge, weld or bolt a replacement matched to the original profile, adjust for plumb against the heaved post, and photograph the finished alignment.
Custom Welding
Signs you need it
Ornamental iron rails are cracked or separated at joints, scrollwork is broken from limb impact, or prior repairs used mismatched material visible to HOA inspection.
What it costs in Marietta
Field welding for rail repair starts at $180-$320; ornamental scrollwork or profile-matched fabrication runs $280-$550 depending on complexity.
How we do it
We clean to bare metal, match the original profile with portable MIG or TIG equipment, apply primer and touch-up paint to HOA color specs, and document the weld penetration and finish in photos.
What Gate Parts & Welding Costs in Marietta
| Item | Typical range in Marietta |
|---|---|
| Hinge replacement (per hinge) | $140-$380 |
| Field welding, rail repair | $180-$320 |
| Custom ornamental welding | $280-$550 |
Can you match my HOA’s original iron profile?
Yes. We photograph the existing profile, reference manufacturer specs where available, and fabricate or source matching material before welding. The homeowner receives photos and a material spec for HOA filing.
Will welding hold if my post keeps heaving?
Welding repairs the gate; post stabilization addresses the cause. We assess post footing depth and drainage, recommend concrete pier extension or bracket adjustment for clay movement, and document both repairs separately.
Brands We Service in Marietta
We service and stock parts for nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our Atlanta-stocked van carries FAAC, BFT, Linear, and Viking control boards and receiver modules for same-day Marietta repair without waiting on shipping. our brands
Pricing for Gate Repair in Marietta, GA
| Service | Typical range in Marietta |
|---|---|
| Keypad entry replacement | $280-$650 |
| Remote receiver replacement | $180-$320 |
| Remote programming (per unit) | $45-$85 |
| Hinge replacement (per hinge) | $140-$380 |
| Field welding, rail repair | $180-$320 |
| Custom ornamental welding | $280-$550 |
Prices in Marietta run higher when HOA finish matching requires custom powder coating or when red clay heave has damaged multiple posts and requires stabilization beyond the gate hardware itself. Every price is written and agreed before work starts under Haven Standard Clause 1; no invoice exceeds the written quote without homeowner approval.
Neighborhoods We Serve in Marietta
We dispatch to Marietta neighborhoods from our Atlanta office, with most East Cobb and downtown-adjacent calls reached within 45 minutes during business hours. Same-day availability depends on call volume and parts needed.
- Indian Hills
- Murdock Road corridors
- Pope High School-area subdivisions
- Downtown Marietta historic district
- Whitlock Avenue corridor
Service Area - Cities Near Marietta
Our crews serve Marietta locally and regularly dispatch to neighboring communities. We also take calls from Smyrna, GA, Roswell, GA, Holly Springs, GA, and Alpharetta, GA for gate repair, access control, and welding work. Scheduling is coordinated from our Atlanta office with local technicians assigned by proximity.
Serving Marietta, GA - Our Local Coverage Area
We’re based in the Marietta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Marietta
You don’t need approval to diagnose or make the gate secure, but visible hardware changes in East Cobb HOA communities typically require architectural review. We provide finish specs and photos for your filing, and can install temporary matching hardware while you wait.
Most Marietta calls are scheduled same-day or next-day depending on time of call and parts required. A live person answers (678) 679-2152 24/7 to assess urgency and dispatch; emergency calls for inoperable security gates get priority.
Most residential gate repair and access control replacement doesn’t trigger permitting, but new installation or structural post replacement may require Cobb County review. We identify permit needs during our free estimate and include documentation in the written scope if required.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Marietta Customers Say
"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.